Revision history [back]

Dear all,

I'm having problems in adding more than one CIM5OW model (induction motor) to the network. Every time I run the dynamic simulation, it crashes down. I'm basically using OWNER 1 for some loads, and OWNER 2 to some other.

1 'CIM5OW'            *            2    0.099   0.112   2.26    0.086   0.102   0   0   1   0.03    1.2 0.04    0   1   0.737   0.9 100 10  0   0.85/ 

2 'CIM5OW'            *            2    0.098   0.111   2.25    0.085   0.101   0   0   1   0.03    1.2 0.04    0   1   0.736   0.9 100 10  0   0.85/

I've tried to change the IDs of the loads per OWNER, and even using all loads with different IDs. Any idea what might be causing it?

NOTE: When using only one CIM5OW model it works, but I had to reduce the DELT value from 10ms to 1ms, otherwise PSS/E would crash as well.

Thank you all,

Nuno F.

Dear all,

I'm having problems in adding more than one CIM5OW model (induction motor) to the network. Every time I run the dynamic simulation, it crashes down. I'm basically using OWNER 1 for some loads, and OWNER 2 to some other.

1 'CIM5OW'            *            2    0.099   0.112   2.26    0.086   0.102   0   0   1   0.03    1.2 0.04    0   1   0.737   0.9 100 10  0   0.85/ 

2 'CIM5OW'            *            2    0.098   0.111   2.25    0.085   0.101   0   0   1   0.03    1.2 0.04    0   1   0.736   0.9 100 10  0   0.85/

I've tried to change the IDs of the loads per OWNER, and even using all loads with different IDs. Any idea what might be causing it?

NOTE: When using only one CIM5OW model it works, but I had to reduce the DELT value from 10ms to 1ms, otherwise PSS/E would crash as well.

Thank you all,

Nuno F.

Dear all,

I'm having problems in adding more than one CIM5OW model (induction motor) to the network. Every time I run the dynamic simulation, it crashes down. I'm basically using OWNER 1 for some loads, and OWNER 2 to some other.

1 'CIM5OW'            *            2    0.099   0.112   2.26    0.086   0.102   0   0   1   0.03    1.2 0.04    0   1   0.737   0.9 100 10  0   0.85/ 

2 'CIM5OW'            *            2    0.098   0.111   2.25    0.085   0.101   0   0   1   0.03    1.2 0.04    0   1   0.736   0.9 100 10  0   0.85/

I've tried to change the IDs of the loads per OWNER, and even using all loads with different IDs. Any idea what might be causing it?

NOTE: When using only one CIM5OW model it works, but I had to reduce the DELT value from 10ms to 1ms, otherwise PSS/E would crash as well.

Thank you all,

Nuno F.

Dear all,

I'm having problems in adding more than one CIM5OW model (induction motor) to the network. Every time I run the dynamic simulation, it crashes down. I'm basically using OWNER 1 for some loads, and OWNER 2 to some other.

1 'CIM5OW'            *            2    0.099   0.112   2.26    0.086   0.102   0   0   1   0.03    1.2 0.04    0   1   0.737   0.9 100 10  0   0.85/ 

2 'CIM5OW'            *            2    0.098   0.111   2.25    0.085   0.101   0   0   1   0.03    1.2 0.04    0   1   0.736   0.9 100 10  0   0.85/

I've tried to change the IDs of the loads per OWNER, and even using all loads with different IDs. Any idea what might be causing it?

NOTE: When using only one CIM5OW model it works, but I had to reduce the DELT value from 10ms to 1ms, otherwise PSS/E would crash as well.

Thank you all,

Nuno F.

Dear all,

I'm having problems in adding more than one CIM5OW model (induction motor) to the network. Every time I run the dynamic simulation, it crashes down. I'm basically using OWNER 1 for some loads, and OWNER 2 to some other.

1 'CIM5OW'            *            2    0.099   0.112   2.26    0.086   0.102   0   0   1   0.03    1.2 0.04    0   1   0.737   0.9 100 10  0   0.85/ 

2 'CIM5OW'            *            2    0.098   0.111   2.25    0.085   0.101   0   0   1   0.03    1.2 0.04    0   1   0.736   0.9 100 10  0   0.85/

I've tried to change the IDs of the loads per OWNER, and even using all loads with different IDs. Any idea what might be causing it?

NOTE: When using only one CIM5OW model it works, but I had to reduce the DELT value from 10ms to 1ms, otherwise PSS/E would crash as well.

Thank you all,

Nuno F.

Dear all,

I'm having problems in adding more than one CIM5OW model (induction motor) to the network. Every time I run the dynamic simulation, it crashes down. I'm basically using OWNER 1 for some loads, and OWNER 2 to some other.

1 'CIM5OW'            *            2    0.099   0.112   2.26    0.086   0.102   0   0   1   0.03    1.2 0.04    0   1   0.737   0.9 100 10  0   0.85/ 

2 'CIM5OW'            *            2    0.098   0.111   2.25    0.085   0.101   0   0   1   0.03    1.2 0.04    0   1   0.736   0.9 100 10  0   0.85/

I've tried to change the IDs of the loads per OWNER, and even using all loads with different IDs. Any idea what might be causing it?

NOTE: When using only one CIM5OW model it works, but I had to reduce the DELT value from 10ms to 1ms, otherwise PSS/E would crash as well.

Thank you all,

Nuno F.