Revision history [back]

Hi Everyone,

I have performed a dynamic simulation using a simple SMIB system to investigate the change of voltage after switching a shunt reactor into the system.

However, the bus voltage cannot recover to the original voltage level (ie. 1p.u.).

www.dropbox.com/s/05xp9s66t740opr/123.JPG?dl=0

Is there any possible solutions to make the bus voltage to recovery to a desired voltage level ?

Thank you so much!

Hi Everyone,

I have performed a dynamic simulation using a simple SMIB system to investigate the change of voltage after switching a shunt reactor into the system.

However, the bus voltage cannot recover to the original voltage level (ie. 1p.u.). 1p.u.) as shown below:

www.dropbox.com/s/05xp9s66t740opr/123.JPG?dl=0

Is there any possible solutions to make the bus voltage to recovery to a desired voltage level ?

Thank you so much!

Hi Everyone,

I have performed a dynamic simulation using a simple SMIB system to investigate the change of voltage after switching a shunt reactor into the system.

However, the bus voltage cannot recover to the original voltage level (ie. 1p.u.) as shown below:

www.dropbox.com/s/05xp9s66t740opr/123.JPG?dl=0

Is there any possible solutions to make the bus voltage to recovery to a desired voltage level ?

Thank you so much!

Hi Everyone,

I have performed a dynamic simulation using a simple SMIB system to investigate the change of voltage after switching a shunt reactor into the system.

However, the bus voltage cannot recover to the original voltage level (ie. 1p.u.) as shown below:

www.dropbox.com/s/05xp9s66t740opr/123.JPG?dl=0

Is there any possible solutions to make the bus voltage to recovery to a desired voltage level ?

if I desire to use the four models: GENROU, EXST1, IEESGO and IEEEST for the generators, is there any method to increase the generator voltage output ?

Thank you so much!

Hi Everyone,

I have performed a dynamic simulation using a simple SMIB system to investigate the change of voltage after switching a shunt reactor into the system.

However, the bus voltage cannot recover to the original voltage level (ie. 1p.u.) as shown below:

www.dropbox.com/s/05xp9s66t740opr/123.JPG?dl=0

Is there any possible solutions solution to make the bus voltage to recovery to a desired voltage level ?

if I desire to use the four models: GENROU, EXST1, IEESGO and IEEEST for the generators, is there any method to increase the generator voltage output / excitation ?

Thank you so much!

Hi Everyone,

I have performed a dynamic simulation using a simple SMIB system to investigate the change of voltage after switching a shunt reactor into the system.

However, the bus voltage cannot recover to the original voltage level (ie. 1p.u.) as shown below:

www.dropbox.com/s/05xp9s66t740opr/123.JPG?dl=0

Is there any possible solution to make the bus voltage to recovery to a desired voltage level ?

if I desire to use the four models: GENROU, EXST1, IEESGO and IEEEST for the generators, is there any method to increase the generator voltage output / excitation as well as the bus volatage ?

Thank you so much!

Hi Everyone,

I have performed a dynamic simulation using a simple SMIB system to investigate the change of voltage after switching a shunt reactor into the system.

However, the bus voltage cannot recover to the original voltage level (ie. 1p.u.) as shown below:

www.dropbox.com/s/05xp9s66t740opr/123.JPG?dl=0

Is there any possible solution to make the bus voltage to recovery to a desired voltage level ?

if I desire to use the four models: GENROU, EXST1, IEESGO and IEEEST for the generators, is there any method to increase the generator voltage output as well as the bus volatage ?

Thank you so much!