Revision history [back]

Hi everyone,

I am attempting to run a dynamic simulation with the PSSE model. Specifically, I am simulating the frequency response of the model and comparing it with the measured data.

I have used the Playback model PLBVFU1 to apply the measured voltage at the HV level, and I adjusted the frequency to match the one forced on the PPC.

I am sharing the results with you: https:// ibb.co/L1sdf1J

the model performs well for active power, but the reactive power does not match the measurements and varies significantly. Additionally, the voltage at the PCC has changed a little bit.

Could you assist me with this and provide any insights or suggestions for improvement?

Hi everyone,

I am attempting to run a dynamic simulation with the PSSE model. Specifically, I am simulating the frequency response of the model and comparing it with the measured data.

I have used the Playback model PLBVFU1 to apply the measured voltage at the HV level, and I adjusted the frequency to match the one forced on the PPC.

I am sharing the results with you: https:// ibb.co/L1sdf1Jhttps://ibb.co/L1sdf1J (delete)

the model performs well for active power, but the reactive power does not match the measurements and varies significantly. Additionally, the voltage at the PCC has changed a little bit.

Could you assist me with this and provide any insights or suggestions for improvement?

Hi everyone,

I am attempting to run a dynamic simulation with the PSSE model. Specifically, I am simulating the frequency response of the model and comparing it with the measured data.

I have used the Playback model PLBVFU1 to apply the measured voltage at the HV level, and I adjusted the frequency to match the one forced on the PPC.

I am sharing the results with you: https://ibb.co/L1sdf1J (delete)https://*ibb.co/L1sdf1J

the model performs well for active power, but the reactive power does not match the measurements and varies significantly. Additionally, the voltage at the PCC has changed a little bit.

Could you assist me with this and provide any insights or suggestions for improvement?

Hi everyone,

I am attempting to run a dynamic simulation with the PSSE model. Specifically, I am simulating the frequency response of the model and comparing it with the measured data.

I have used the Playback model PLBVFU1 to apply the measured voltage at the HV level, and I adjusted the frequency to match the one forced on the PPC.

I am sharing the results with you: https://*ibb.co/L1sdf1Jhttps://*ibb.co/L1sdf1J (delete *)

the model performs well for active power, but the reactive power does not match the measurements and varies significantly. Additionally, the voltage at the PCC has changed a little bit.

Could you assist me with this and provide any insights or suggestions for improvement?

Hi everyone,

I am attempting to run a dynamic simulation with the PSSE model. Specifically, I am simulating the frequency response of the model and comparing it with the measured data.

I have used the Playback model PLBVFU1 to apply the measured voltage at the HV level, and I adjusted the frequency to match the one forced on the PPC.

I am sharing the results with you: https://*ibb.co/L1sdf1J (delete *)

the model performs well for active power, but the reactive power does not match the measurements and varies significantly. Additionally, the voltage at the PCC has changed a little bit.

Could you assist me with this and provide any insights or suggestions for improvement?

Hi everyone,

I am attempting to run a dynamic simulation with the PSSE model. Specifically, I am simulating the frequency response of the model and comparing it with the measured data.

I have used the Playback model PLBVFU1 to apply the measured voltage at the HV level, and I adjusted the frequency to match the one forced on the PPC.

I am sharing the results with you: https://*ibb.co/L1sdf1J https://*ibb.co/ctqsnHp (delete *)

the model performs well for active power, but the reactive power does not match the measurements and varies significantly. Additionally, the voltage at the PCC has changed a little bit.

Could you assist me with this and provide any insights or suggestions for improvement?